THE EFFECT OF ABRASIVE GRAIN SHAPES ON QUALITY OF FERRITE MAGNETS GRINDING PROCESS
DOI:
https://doi.org/10.29122/mipi.v14i2.4170Abstract
A research was conducted on the grinding process of ferrite magnet with Strontium ferrite type (SrO.6 (Fe2O3)) using electroplated single layer grinding wheels. Many cracks have been found on work pieces during this work, which is coming from grinding processes. Research is conducted starting from chemical composition test and the effect of the shape and size of the abrasive grain of grinding wheels to the quality of grinding process results by measuring crack ratio of the work piece. In this experiment, 3 (three) model design of grinding wheels with three different size and shape of abrasive grains are made. All of processing parameters are set at the same value as ordinary process. The experimental results shown that 3rd model have the best results from the outputs number and also the lowest reject crack ratio compared to 1st and 2nd models. This is because the 3rd model has blocky shape which its distribution structure is denser and more uniform compared to the irregular shape, so that continuous grinding on hard and brittle work pieces is more stable and suitable
References
"https://www.nortonabrasives.com/sites/sga.na.com," 1 January 2014. [Online]. Available: https://www.nortonabrasives.com/sites/sga.na.com/files/document/27946_9.pdf. [Accessed saturday october 2018]
S. M. Z.Shl, "An investigation of grinding with electroplated CBN Wheels," Journal of Materials Processing Technology, vol. 1, no. 2002, pp. 1-4, 2002
T. H. S.Malkin, "Department of Mechanical b Industrial Engineering, Engineering Lab Building,," Grinding Mechanism for ceramics, no. 12, pp. 1-12, 1989.
O. G. &. C. S. Frittz Klocke, Green Machining of Advances Ceramics, Fraunhofer Institute of Production Technology, Aachen, Germany
B. J.C. Aurich, "Kinematic simulation of high-performance grinding for analysis of chip parameters of single grains," CIRP Journal of Manufacturing Science and Technology, vol. 5, no. 3, pp. 164-174, 2012.
A. F. B. C. Tianyu Yu, "Modeling Wear Process of Electroplated CBN Grinding Wheel," ASME 2015 International Manufacturing Science and Engineering Conference, vol. 1, no. ISBN: 978-0-7918-5682-6, p. 7, 2015.
HMSO, Lubrication (Tribology) Education and Research, DES (Jost) Report., London, 1966.
HMSO, Lubrication (Tribology) Education and Research, DES (Jost) Report, London, 1966.
H. Czichos, Tribology—A Systems Approach to the Science and Technology of Friction, Lubrication and Wear., Elsevier Press., 1978.
W. Rowe, Principles of Modern Grinding Technology. Elsevier, William Andrew, 2009.
P. D. M. Faurre, Elements of System Theory, Amsterdam, Holland., 1977.
H. Czichos, "Tribology—A Systems Approach to the Science and Technology o fFriction, Lubrication and Wear. Elsevier Press.," 1978.
K. Zum Gahr, Microstructure and Wear of Materials. Elsevier, Amsterdam, Holland., 1987.
I. H. M. U. E. R. W. I. I. Marinescu, Handbook of Machining with Grinding Wheels., CRC Press., 2007.
A. F. B. A. C. Tianyu Yu, "Experimental Characterization of Electroplated CBN Grinding Wheel Wear: Topology Evolution and Interfacial Toughness," ASME 2014 International Manufacturing Science and Engineering Conference collocated with the JSME 2014 International Conference on Materials and Processing and the 42nd North American Manufacturing Research Conference, vol. 1, p. 8, 2014.
O. G. C. S. Fritz Klocke, Machining of Ceramic and composites.
J.E.R.S.Malkin, Grinding Mechanisms Strength Degradationfor Ceramics., 1991.
J. F. S. M. R.P. Upadhyaya, "Factors Affecting Grinding Performance with Electroplated CBN Wheels.," Journal of Engineering for Industry , vol. 111, no. 1989, pp. 167-174, 2007.
"www.," saint-gobain, 12 10 2003. [Online]. Available: www.saint-gobain.com. [Accessed 1 January 2018].
Bina Produktivitas Kerja, Jakarta: Departemen Tenaga Kerja, 1998.
C. W. S. H. F. H. K. W. M. Warhanek, "Cutting characteristics of electroplated diamond tools with laser-generated positive clearance," CIRP Annals, vol. 64, no. 1, pp. 317-320, 2015.
S. G. C. Malkin, Grinding Technology, Industrial Press, 2008.
A. Ahyari, Manajemen produksi, Pengendalian Produksi, Yogyakarta: BPFE, 1990.
A. Ahyari, Prosedur Penelitian Suatu Pendekatan Praktik, Jakarta: Bina Aksara , 1989.
D. Beers, Diamond and CBN Grit Products.
W. R. B. D. &. H. O. I. Marinescu, Tribology of Abrasive Machining Processes, second edition., William Andrew Publishing, 2004.
M. H. E. U. W. B. R. I. I. Ioan D. Marinescu, Handbook of Machining with Grinding Wheels, London: CRC Press Taylor & Francis Group, 2007.
O. G. J.C Aurich, "Development of a Superabrasive Grinding Wheel with defined Grain structure using kinematic simulation," Precision manufacturing Journal, vol. 1, no. 1, pp. 1-6, 1986.
A. Sofjan, Manajemen Produksi dan Operasi, Jakarta: Fakultas Ekonomi Universitas Indonesia, 1998.
Downloads
Published
How to Cite
Issue
Section
License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
Open Access Policy
MIPI provides immediate open access to its content on the principle that making research freely available to the public supports a greater global exchange of knowledge.
MIPI by BRIN is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License. Permissions beyond the scope of this license may be available at http://ejurnal.bppt.go.id/index.php/MIPI