MECHANOSYNTHESIS OF MMC Cu-C DOPED WITH Ti FOR APPLICATION OF PANTOGRAPH CONTACT STRIP (PCS)

Authors

  • Andhika Abdan Rahmanullah Metallurgy Engineering, Faculty of Manufacture Engineering - UNJANI
  • Pawawoi Pawawoi Metallurgy Engineering, Faculty of Manufacture Engineering - UNJANI
  • Djoko Hadi Prajitno Center for Nuclear Science and Technology Application

DOI:

https://doi.org/10.29122/mipi.v14i3.4168

Keywords:

MMC CuC, Mechanical Alloying, Titanium, Pantograph Contact Strip

Abstract

This research was conducted to determine the effect of the addition of Titanium (Ti) and the sintering temperature variation on MMC CuC alloys as reinforcing elements. The process of this research uses powder metallurgical method with an alloying technique in Mechanical Alloying using a Planetary Ball Mill (PBM) machine with a speed of 600 rpm for 2 hours, the ratio of powder to the ball mill is 10:1. The compacting process is carried out using dies 11 mm in diameter and compacting pressure of 90 Kg/cm2. The sintering process is carried out three times, with variations in sintering of 800oC, 900oC, and 1000oC with sintering time for 1 hour in the tube furnace in the argon gas vacuum environment. The number of samples used in this study amounted to 9 samples with variations in alloy and temperature sintering, consist of MMC CuC alloy with addition of Ti 0%, 0.5%, 1.5% (T=800 oC), MMC CuC with  addition of Ti 0%, 0.5%, 1.5% (T=900 oC), and MMC CuC with addition of Ti 0%, 0.5%, 1.5% (T=1000 oC). The tests included Vickers hardness testing, metallography testing, XRD testing, and SEM-EDS testing. The addition of Ti elements and varying sintering temperature had an effect on the hardness value of MMC CuC material with the highest hardness value in samples with 1.5% Ti alloy (800oC) which is 87.25 HV, and the lowest porosity value is 2.491% in the sample of 1.5% Ti (1000oC).

References

Liu, Z., Numerical Study on Multi-pantograph Railway Operations at High Speed, Thesis in Vehicle and Maritime Engineering, KTH Royal Institute of Technology, Sweden, 2015.

Deng, C., Yin, J., Zhang, H., Xiong, X., Wang, P., and Sun, M., The Tribological Properties of Cf/Cu/C Composites Under Applied Electric Current, Tribol. Int., Vol. 116, December 2017, p.84-94.

Fadhila, M.N., Jakarta's Commuter Line Train Gets Ready for More Passengers in 2018,

https://republika.co.id/berita/nasional/jabodetabek-nasional/18/01/04/p20z6k383-operator-krl-commuter. Accessed in November 2020.

Arnold, M., and Simeon, B., Pantograph and Catenary Dynamics: A Benchmark Problem and its Numerical Solution, Appl. Numer. Math., Vol. 34, No. 4, 2000, p. 345–362.

Wu, G., Wei, W., Gao, G., Wu, J., and Zhou, Y., Evolution of the Electrical Contact of Dynamic Pantograph–Catenary System, J. Mod. Transp., Vol. 24, No. 2, 2016, p.132–138.

Cohen, M., Addison-Wesley Metallurgy Series, Addison-Wesley Publishing Company, Inc., Massachusetts, 1956.

Girão, A.V., Caputo, G., and Ferro, M.C., Application of Scanning Electron Microscopy–Energy Dispersive X-Ray Spectroscopy (SEM-EDS), Compr. Anal. Chem., Vol. 75, 2017, p.153–168.

Dieter, G.E., Mechanical Metallurgy: by George E. Dieter, Jr. 615 pages, diagrams, illustrations, 6 × 9 in. New York, McGraw-Hill Book Co., Inc., 1961. Price, $12.50, Journal of the Franklin Institute, Vol. 273, No. 4, 1962, p.338.

Ruwaida, A.F., Widyastuti, and Rochiem, R., Sintesis MMCs Cu-Al2O3 Melalui Proses Metalurgi Serbuk dengan Variasi Fraksi Volum Al2O3 dan Temperatur Sintering, https://adoc.tips/al-2-o-3-melalui-proses-metalurgi-serbuk-dengan-variasi-frak.html. Accessed on March 2020.

Davis, J.R., and Associates, ASM Specialty Handbook: Copper and Copper Alloys, ASM International, Materials Park, OH 44073-0002, USA, 2001.

Ngai, T.L., Zheng, W., and Li, Y., Effect of Sintering Temperature on the Preparation of Cu–Ti3SiC2 Metal Matrix Composite, Prog. Nat. Sci. Mater. Int., Vol. 23, No. 1, 2013, p.70–76.

ASTM E112-10, Standard Test Methods for Determining Average Grain Size, ASTM International, West Conshohocken, PA, 2010, www.astm.org.

Mataram, A., and Rochardjo, H.S.B., MAT/19-31P Physical and Mechanical Properties of Composite Copper/Carbon, Proceeding of ICCS 2007, Yogyakarta-Indonesia, 24-25 May 2007.

Upadhyaya, G.S., Powder Metallurgy Technology, Cambridge International Science Publishing, England, 2002.

Lubis, K., Metoda-Metoda Karakterisasi Nanopartikel Perak, Jurnal Pengabdian Kepada Masyarakat., Vol. 21, No. 79, 2015, p.50–55

Downloads

Published

13-09-2023

How to Cite

Rahmanullah, A. A., Pawawoi, P., & Prajitno, D. H. (2023). MECHANOSYNTHESIS OF MMC Cu-C DOPED WITH Ti FOR APPLICATION OF PANTOGRAPH CONTACT STRIP (PCS). Majalah Ilmiah Pengkajian Industri; Journal of Industrial Research and Innovation, 14(3), 233–242. https://doi.org/10.29122/mipi.v14i3.4168

Issue

Vol. 14 No. 3 (2020): Majalah Ilmiah Pengkajian Industri; Journal of Industrial Research and Innovation

Section

Articles

License

Creative Commons License

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Open Access Policy

MIPI provides immediate open access to its content on the principle that making research freely available to the public supports a greater global exchange of knowledge.

MIPI by BRIN is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License. Permissions beyond the scope of this license may be available at http://ejurnal.bppt.go.id/index.php/MIPI