Pengaruh Pemesinan Milling Terhadap Kekasaran Permukaan Baja Tahan Karat Martensitik Modifikasi Aisi 410 3Mo – 3Ni dan Keausan Material Cutter End Mill [Effect of Milling Machining on Surface Roughness of AISI 410 3Mo-3Ni Martensitic Stainless Steel and W
Article Sidebar
Main Article Content
Abstract
Process of machining always occurs interaction between cutting tool and workpiece causing chisel or cutting knife experience friction and wear. The purpose of this research is to observe the effect of spindle speed and feed rate on surface roughness of martensitic stainless steel modified AISI 410 3Mo-3Ni and wear of cutter end mill. The method of variance analysis is used in the analysis of machining results. The result of this research is the smallest surface roughness value obtained at 1300 rpm of spindle speed cutting and 190 mm/min of feed rate. The largest surface roughness value obtained on 950 rpm of spindle speed and 760 mm/menit of feed rate. Then, the smallest wear value of edge of cutter endmill of 40.16 μm is found on spindle speed variation of 950 rpm and feed rate 190 mm/min and the largest wear value of edge of cutter end mill of 255.23 μm is found on spindle speed variation of 1300 rpm and feed rate 760 mm/min
Article Details
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
References
E. Mabruri, M. S. Anwar, S. Prifiharni, T. B. Romijarso, dan B. Ajiantoro, “Tensile properties of the modified 13Cr martensitic stainless steels,” AIP Conference Proceedings 1725, 020039, 2016; doi: 10.1063/1.49454932016.
Haryadi, D. Mulyana, “Pembuatan runner turbin propeler menggunakan CNC dan pengujiannya,” Jurnal Metrik, vol. 6, no. 2, pp. 1–7, 2012.
E. L. Houghton, P. W. Carpenter, S. Collicott, dan D. Valentine, Aerodynamics for Engineering Students, 7th edition, pp. 688. Butterworth Heinemann, London, 2016.
T. U. Nugroho, H. Saputro, dan Y. Estriyanto, ”Pengaruh kecepatan pemakanan dan waktu pemberian pendingin terhadap tingkat keausan cutter end mill HSS hasil pemesinan CNC milling pada baja ST 40,” Maj. Nosel, vol. 1, no. 1, pp. 79-89, 2012.
G. Kiswanto, A. S. Danardono, dan S. Wiyono, “Pengaruh parameter pemesinan terhadap kualitas permukaan Baja DF-3 (AISI 01) yang dikeraskan,” Jurnal Teknologi, vol. 3, pp. 185-192, 2005.
M. T. Prado, A. Pereira, J. A. Perez, dan T. G. Mathia,”Methodology for tool wear analysis by a simple procedure during milling of AISI H13 and its impact on surface morphology,” Proceedia Manufacturing, vol. 13, pp. 348-355, 2017.
M. T. Prado, A. Pereira, J. A. Perez, dan T. G. Mathia,” Methodology for tool wear Analysis by electrical measuring during milling of AISI H13 and its impact on surface morphology,” Proceedia Manufacturing, vol. 13, pp. 356-363, 2017.
X. Luan, S. Zhang, J. Li, G. Mendis, F. Zhao, dan J. W. Sutherland,”Trade-off analysis of tool wear, machining quality, and energy efficiency of alloys cast iron milling process,” Procedia Manufacturing, vol. 26, pp. 383-393, 2018.
N. Ambhore, D. Kamble, S. Chinchanikar, dan V. Wayal,” Tool condition monitoring system: A review,” Materials Today:Proceeding, vol. 2, pp. 3419-3428, 2015.
Y. Harsh, Valera, dan S. N. Bhavsar,” Experimental investigation of surface roughness and power consumption in turning operation of EN 31 alloy steel,” Procedia Technology, vol. 14, pp. 528-534, 2014.
N. S. Kumara, A. Shettyb, A. Shettyb, K. Ananth, dan H. Shettyba,” Effect of spindle speed and feed rate on surface roughness of carbon steels in CNC turning,” Procedia Engineering, vol. 38, pp. 691-697, 2012.
O. O. Ayodeji, M. S. Abolarin, J. J. Yisa, P. S. Olaoluwa, dan A. C. Kehinde,” Effect of cutting speed and feed rate on tool wear rate and surface roughness in lathe turning process,” International Journal of Engineering Trends and Technology (IJETT), vol. 22, no. 4, pp. 173-175, 2015.
R. Suresh, dan S. Basavarajappa,”Effect of process parameters on tool wear and surface roughness during turning of hardened steel with coated ceramic tool,” Procedia Materials Science, vol. 5, pp.1450-1459, 2014.
