UTILIZATION OF INDONESIAN LOCAL STANNIC CHLORIDE (SnCl4) PRECURSOR IN THE PROCESS OF MAKING FLUORINE- DOPED TIN OXIDE (FTO) CONDUCTIVE GLASS

Authors

  • Tri Arini Pusat Penelitian Metalurgi dan Material - LIPI Gedung 470 Kawasan Puspiptek - Serpong, Tangerang Selatan 15314
  • Latifa Hanum Lalasari Pusat Penelitian Metalurgi dan Material - LIPI Gedung 470 Kawasan Puspiptek - Serpong, Tangerang Selatan 15314
  • Lia Andriyah Pusat Penelitian Metalurgi dan Material - LIPI Gedung 470 Kawasan Puspiptek - Serpong, Tangerang Selatan 15314
  • Gennady Fahmi Departemen Teknik Metalurgi – Universitas Sultan Ageng Tirtayasa Kawasan Puspiptek - Serpong, Tangerang Selatan 15314
  • F. Firdiyono Pusat Penelitian Metalurgi dan Material - LIPI Gedung 470 Kawasan Puspiptek - Serpong, Tangerang Selatan 15314

DOI:

https://doi.org/10.17146/jsmi.2019.20.2.5469

Keywords:

FTO conductive glass, Indonesian local precursor, ultrasonic spray pyrolysis nebulizer, deposition temperature, tetragonal

Abstract

UTILIZATION OF INDONESIAN LOCAL STANNIC CHLORIDE (SnCl4) PRECURSOR IN THE PROCESS OF MAKING FLUORINE-DOPED TIN OXIDE (FTO) CONDUCTIVE GLASS. Thin layer of fluorine- doped tin oxide (FTO) conductive glass has been deposited on a glass substrate heated at a temperature of 350°C using the ultrasonic spray pyrolysis nebulizer method with variations in fluorine doping and substrate temperatures. This experiment uses the raw material of Indonesian local stannic chloride (SnCl4) (PT Timah Industri) as a precursor with a temperature variation of 250, 300, 350, 400°C. The structure and morphology of the optical and electrical properties of all the thin layers have been examined. XRD results show that all thin layers have a tetragonal crystal structure. In this experiment, there is a significant influence on the role of fluorine doping on resistivity and transmittance values. With the addition of 2% wt doping, the resistivity and transmittance values decrease. The optimum value is obtained by doping 2 wt%, substrate temperature of 350°C with a resistivity value of 9.28.10-5 Ω.cm and transmittance value of 88%.

Downloads

Download data is not yet available.

References

. K. N. Chopra and A. K. Maini, “Thin Films and Their Applications in Military and Civil Sectors,” DRDO Monograps/Special Publ. Ser., p. 22 pages, 2010.

. H. Widiyandari, A. Purwanto, E. Hidayanto, and K. Diharjo, “Fabrikasi Gelas Transparant Konduktif FTO (Flourine-doped Tin Oxide) dan Aplikasinya pada Sel Surya Berbasis Dye (DSSC),” Pros. InSINas, pp. 88–92, 2012.

. L. H. Lalasari, T. Arini, L. Andriyah, F. Firdiyono, and A. H. Yuwono, “Electrical, optical and structural properties of FTO thin films fabricated by spray ultrasonic nebulizer technique from SnCl4 precursor,” in AIP Conference Proceedings, 2018, vol. 20001, pp. 1–7.

. Z. Y. Banyamin, P. J. Kelly, G. West, and J. Boardman, “Electrical and Optical Properties of Fluorine Doped Tin Oxide Thin Films Prepared by Magnetron Sputtering,” Coatings, vol. 4, pp. 732–746, 2014.

. A. A. Yadav, E. U. Masumdar, A. V Moholkar, M. Neumann-spallart, K. Y. Rajpure, and C. H. Bhosale, “Electrical , structural and optical properties of SnO2:F thin films : Effect of the substrate temperature,” J. Alloys Compd., vol. 488, pp. 350–355, 2009.

. G. Muruganantham, K. Ravichandran, and K. Saravanakumar, “Effect of solvent volume on the physical properties of undoped and fluorine doped tin oxide films deposited using a low-cost spray technique,” Superlattices Microstruct., vol. 50, no. 6, pp. 722–733, 2011.

. T. Arini et al., “The Influence of Deposition Time and Substrate Temperature During the Spray Pyrolysis Process on The Electrical Resistivity and Optical Transmittance of 2 Wt% Fluorine Doped Tin Oxide Conducting Glass,” Int. J. Technol., vol. 8, pp. 1335–1343, 2016.

. D. Fikri, A. H. Yuwono, N. Sofyan, T. Arini, and L. H. Lalasari, “The effect of substrate heating temperature upon spray pyrolysis process on the morphological and functional properties of fluorine tin oxide conducting glass,” in AIP Conference Proceedings, 2017, vol. 1826, p. 02003 (1-9).

. A. Kennedy, K. Viswanathan, and K. Pradeev raj, “Study of the influence of substrate temperature on structural, optical, and electrical properties of Zn-doped MnIn 2 S 4 thin films prepared by chemical spray pyrolysis,” Phys. Lett. A, vol. 380, no. 36, pp. 2842–2848, 2016.

. C. A. Trisdianto, A. H. Yuwono, T. Arini, N. Sofyan, D. Fikri, and L. H. Lalasari, “Optical Transmittance, Electrical Resistivity and Microstructural Characteristics of Undoped and Fluorine-Doped Tin Oxide Conductive Glass Fabricated by Spray Pyrolysis Technique with Modified Ultrasonic Nebulizer,” Int. J. Technol., vol. 8, pp. 1316–1325, 2016.

. H. Zhao, Q. Liu, Y. Cai, and F. Zhang, “Effects of water on the structure and properties of F doped SnO2 films,” Mater. Lett., vol. 62, pp. 1294–1296, 2008.

. D. Tatar, G. Turgut, and B. Duzgun, “Effect of substrat temperature on the crystal growth orientation and some physical properties of SnO2:F thin film deposited by spray pyrolisis technique,” J. Phys., vol. 58, pp. 143–158, 2013.

Downloads

Published

31-01-2019

How to Cite

Tri Arini, Latifa Hanum Lalasari, Lia Andriyah, Gennady Fahmi, & F. Firdiyono. (2019). UTILIZATION OF INDONESIAN LOCAL STANNIC CHLORIDE (SnCl4) PRECURSOR IN THE PROCESS OF MAKING FLUORINE- DOPED TIN OXIDE (FTO) CONDUCTIVE GLASS. Jurnal Sains Materi Indonesia, 20(2), 62–66. https://doi.org/10.17146/jsmi.2019.20.2.5469

Issue

Vol. 20 No. 2 (2019): Jurnal Sains dan Materi Indonesia

Section

Articles

License

Creative Commons License

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.