MICROSTRUCTURE AND PHASE TRANSFORMATION OF PURE TITANIUM DURING NITRIDING PROCESS BY HIGH DENSITY PLASMA
DOI:
https://doi.org/10.17146/jsmi.2017.18.3.4115Keywords:
Pure Titanium, Titanium Murni, RF-DC, Sistem Plasma, Plasma System, Low Temperature Nitriding, Nitriding Pada Suhu Rendah, Omega Titanium, Increasing Surface Hardness, Peningkatan Kekerasan permukaanAbstract
MICROSTRUCTURE AND PHASE TRANSFORMATION OF PURE TITANIUM DURING NITRIDING PROCESS BY HIGH DENSITY PLASMA. Low temperature nitriding process at a temperature of 450°C has been carried out in order to increase the surface hardness of pure titanium. The plasma nitriding process was utilized by high density RF-DC system with an addition of a hollow cathode device. The plasma was generated by RF generator with the frequency of 2 MHz and attract directly to the cathode plate by high voltage DC bias of -500 to -600 V. The plasma of N2/H2 gases with a flow rate of 160/40 mL/min in gas pressure of 75, 50, and 30 Pa was used in nitriding process for 4h and 8h. The occurrence of phase transformation of -Ti to w-Ti triggers the formation of TiN as a nitride layer. The formation of TiN and the diffusion of nitrogen into a titanium matrix can increase the surface hardness of pure titanium up to 792.0 HV.
ABSTRAK
STRUKTURMIKRO DAN TRASFORMASI FASATITANIUM SELAMA PROSES NITRIDASI DENGAN HIGH DENSITY PLASMA. Proses nitriding pada suhu 450°C berhasil dilakukan untuk meningkatkan tingkat kekerasan logam titamium murni. Proses nitriding menggunakan plasma berdensitas tinggi yang dihasilkan oleh sistem RF-DC dengan penambahan perangkat hollow cathode. Plasma dibangkitkan oleh RF generator yang berfrekuensi 2 MHz dan ditarik menuju plat katoda oleh tegangan tinggi suatu bias DC sebesar -500 V atau -600 V. Plasma yang terbentuk dari campuran gas nitrogen dan gas hidrogen dengan laju aliran sebesar 160/40 mL/menit pada tekanan gas sebesar 75, 50, dan 30 Pa digunakan pada proses nitriding selama 4 jam atau 8 jam. Hasil yang didapat adalah terjadinya perubahan fase dari α-Ti menjadi ω-Ti yang sekaligus menjadi pemicu terbentuknya TiN sebagai lapisan nitride. Pembentukan TiN dan terjadinya difusi dari atom nitrogen ke dalam matriks logam titanium berhasil meningkatkan kekerasan permukaan logam titanium hingga mencapai nilai 792,0 HV.
Downloads
References
D. K. Peacock. “Titanium.” in Construction Materials Reference, 2nd edition. David Doran and Bob Chater, Ed. NewYork: Routledge, pp. 109-118, 2014.
L. J. Bartlo and D. J. McNeish. “Mettalography of Titanium and Its Alloys” in Titanium-Physical Metalurgy, Processing and Application, 1st edition. F. H. Froes, Ed. Ohio: ASM International, pp. 141-159, 2015
Y. Matychak, I. Pohrelyuk, V. Fedirko and O. Tkachuk. “Modelling of Microstructural Evolution of Titanium During Diffusive Saturation by
Interstitial Elements” in TitaniumAlloys-Advances in Property Control. J. Sieniawski , Ed. (1st Edition) InTech. 2013.
M. Khandaker, S. Riahinezhad,Y. Li, M. B. Vaughan, F. Sultana, T.L. Morris, L. Phinney and K. Hossain. “Plasma Nitriding of Titanium Alloy: Effect Of Roughness, Hardness, Biocompatibility, And Bonding With Bone Cement.” Bio-Medical Materials and Engineering, vol. 27, pp. 461 474, 2016.
E. Koyuncu, F. Kahraman and O. Karadeniz. “Investigation of Surface Properties of HighTemperature Nitrided TitaniumAlloys.” Journal of Achievement in Material and Manufacturing Engineering, vol. 37, no. 2, pp. 434-441, 2009.
X. Wang, S. Bai, F. Li, D. Li, J. Zhang, M. Tian, Q. Zhang, Y. Tong, Z. Zhang, G. Wang, T. Guo, and C. Ma. “Effect of Plasma Nitriding and Titanium Nitride Coating on The Corrosion Resistance Of Titanium.” The Journal of Prosthetic Dentistry, pp. 1-7, 2016.
N. A. Zarkevich and D. D. Johnson. (2015, Oct.). “Titanium -Phase Transformation Pathway and a Predicted Metastable Structure.” Phys Rev B. pp. 1-5, 2017.
N. Adachi, Y. Todaka, K. Irie, and M. Umemoto. “Phase Transformation Kinetics of -phase in Pure Ti Formed by High-Pressure Torsion. J Mater Sci, vol. 51, pp. 2608-2615, 2016.
R.G. Hennig, D.R. Trinkle, J. Bouchet, S.G.Srinivasan, R.C. Albers, and J.W. Wilkins. “Impurities Block The α to ω Martensitic Transformation in Titanium.” Nature Materials, vol. 4, pp. 129-133, 2005.
Dehai Ping. “Review on ω Phase in Body-Centered Cubic Metals and Alloys.” Acta Metall. Sin. (Engl. Lett.), vol. 27, no. 1, pp. 1-11, 2014.
I. Çelik and M. Karakan. “Effect of Plasma Nitriding Treatment on Structural, Tribological And Electrochemical Properties Of Commercially Pure Titanium.” In Proc IMechE Part H : J Engineering in Medicine 1-8, pp. 1-8, 2015.
Yu F. Ivanov, Yu H. Akhmadeev, I. V. Lopatin, E. A. Petrikova, O. V. Krysina, and N. N. Koval. “Structure and Properties Of Commercially Pure Titanium Nitrided in The Plasma Of A Low-Pressure Gas Discharge Produced by a PINK Plasma Generator.” in 12th International Conference on Gas Discharge Plasmas and Their Applications, IOP Publishing, Journal of Physics: Conference Series 652 (012013), 2015, pp. 1-6.
I. M. Pohrelyuk, S. E. Sheykin, S. M. Dub, A. G. Mamalis, I. Yu Rostotskii, O. V. Tkachuk, and S. M. Lavrys. “Increasing of Functionality of c.p.Titanium/UHMWPE Tribo-Pairs by Thermodiffusion Nitriding of Titanium Component,” Biotribology , vol 7, pp. 38-45, 2016.
L. Bárdoš. “Radio Frequency Hollow Cathodes for The Plasma Processing Technology.” Surface and Coatings Technology, vol. 86-87, pp. 648-656, 1996.
I. M. Pastukh, N. S. Mashovets, Yu. I. Shalapko and V. A. Kurskaja. “Forecast The Formation of Nitrides on The Surface of Titanium Alloys During Nitriding In AGlow Discharge.” Journal ofAchievements in Materials and Manufacturing Engineering, vol. 62, no. 2, pp. 53-62. 2014.
T. Aizawa. Photograph Of The High Density RF-DC Plasma System at LLC Nanofilm & Coat Laboratory, Ota-ku, Tokyo, Japan. (private communication)
M. Yoshida, R. Ichiki, and N. Utsumi. “Surface Hardening of Titanium Using Gas Nitriding,” J. of Precision Engineering and Manufacturing, vol 14, no, 6, pp. 971-976. 2013.
E. E. Yunata, T. Aizawa, and D. J. H. D. Santjojo. “Characterization Of Hollow Cathode Plasma for Etching And Ashing Processes.” in 8th SEATUC Meeting and Symposium, OS, vol. 6, no. 14, pp. 1-4, 2014.
J. M. Windajanti, D. J. D. H. Santjojo and Abdurrouf. “Low Temperature Nitriding of Pure Titanium Using Hollow Cathode RF-DC Plasma.” IOP Conference Series : Materials Science and Engineering, vol. 202, 2017.
I. Pohrelyuk and V. Fedirko. “Chemico-Thermal Treatment of Titanium Alloys-Nitriding,” in Titanium Alloys-Towards Achieving Enhanced Properties for DiversifiedApplications, pp.141-174. A. K. M. NurulAmin, Ed. (1st Edition). InTech. 2012.
H. J. Brading, P. H. Morton, T. Bell,and L. G. Earwaker. “Plasma Nitriding with Nitrogen, Hydrogen, and Argon Gas Mixtures: Structure and Composition of Coating on Titanium.” Surface Engineering, vol. 8, no. 3, pp. 206-212, 1992.
A. Gicouel, N. Laidani, P. Saillard, and J. Amouroux. “Plasma and Nitrides : Application to The Nitriding of Titanium.” J. Pure & Applied Chem., vol. 62, no. 9, pp. 1743-1750, 1990
Downloads
Published
How to Cite
Issue
Section
License

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.





