Design and experimental Verification of Vibration Testing Fixture for Flight Control Panel
DOI:
https://doi.org/10.30536/j.jtd.2021.v19.a3701Keywords:
Test Fixture, Vibration, Natural Frequency, ShakerAbstract
In this research, experimental design and testing of the vibration test fixture were carried out. The designed vibration test fixture is used to test the FCP, which is one of the components of avionics in aircraft. FCP vibration testing is carried out using the DO-160 test standard. The test has a test frequency range from 5 to 500 Hz. Therefore, the vibration test fixture must have a natural frequency above 600 Hz. The vibration test fixture is designed using a T-type model with modifications to get optimal results. The raw material used to make the test fixture is aluminum. The test fixture has a natural frequency value above 500 Hz, and both were tested using FEM simulation and experimental tests. Therefore, the vibration test fixture that is made meets the requirements for vibration testing on FCP. The difference in the natural frequency value from the FEM simulation and experimental test results on the vibration test fixture is 14.61% on the Z-axis, 10.61% on the X-axis, and 9.74 on the Y-axis.
References
(RTCA), R. T. C. for A. (2010). DO-160, Environmental Conditions and Test Procedures for Airborne
Equipment.
De Barros, E., & Souto, C. D. A. (2017). Evaluation of a Vibration Text Fixture. International Journal of
Acoustics and Vibrations, 22(3), 349–352. https://doi.org/10.20855/ijav.2017.22.3480
E, S., Gidaveer, R. S., N, S., Patil, S. K., K, A. K., & J, E. (2020). Design and Analysis of Vibration Test Fixture
for 6.2 kW Siemens[R] Motor. International Journal of Innovative Research in Science, Engineering and
Technology (IJIRSET), 9(5), 3539–3546.
Fábry, S., & Češkovič, M. (2017). Aircraft gas turbine engine vibration diagnostics. MAD - Magazine of
Aviation Development, 5, 24–28. https://doi.org/10.14311/mad.2017.04.04
Klee, B. J., Kimball, D. V., & Tustin, W. (1971). Vibration and Shock Test Fixture Design: Design,
Fabrication, and Evaluation. Tustin Institute of Technology.
Rahman, A. H., Sivakumar, P., V, B., & Jagath, R. K. (2016). Design of a Composite Vibration Fixture for
Testing Fuel Tank for Combat Vehicle Application. International NAFEMS Conference on Engineering
Analysis, Modeling, Simulation and 3D-Printing (NAFEMS-3D), August.
Reddy, A., K, H., & Petunias, H. S. (2016). Design and Development of Vibration Testing Fixtures.
International Journal of Students’ Research in Technology & Management, 4(1), 08–11. https://doi.org/10.18510/ijsrtm.2016.413
Reddy, T. S., Vijaya, K., & Reddy, K. (2010). Design and analysis of vibration test bed fixtures for space
launch vehicles. Indian Journal of Science and Technology, 3(5). http://www.indjst.org
Srinivas, P., & Ravikumar, T. (2017). Design of Vibration Test Fixture for Opto-Electronic Equipment.
International Journal Of Modern Engineering Research (IJMER), 7, 32–37.
Ula, N. M., Wijaya, Y. G., Muksin, M., Pratama, M. G. P. P., & Syah, A. H. N. (2020). Dynamical Characteristics
Of A Head Expander For Vibration Testing In Pustekbang Laboratory. Angkasa: Jurnal Ilmiah Bidang
Teknologi, 12(2), 167–174. https://doi.org/10.28989/ANGKASA.V12I2.773
Venkat, Varun, Kumar Singh, A., Srikrishna, Mudda, S., & Jhorar, R. (2016). Design, Analysis and Testing of
Multi-axis Vibration Fixture for Electronic Devices. Indian Journal of Science and Technology, 9(34). https://doi.org/10.17485/ijst/2016/v9i34/100895
Wirawan, A., & Jayanti, E. B. (2019). Desain Awal Flight Control Panel Dari Pesawat Lsa-02. Seminar
Nasional Instrumentasi, Kontrol Dan Otomasi (SNIKO), 2, 10–11. https://doi.org/10.5614/sniko.2018.2
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2021 Yusuf Giri Wijaya, Nur Mufidatul Ula, Mikhael Gilang Pribadi P.P., Muksin, Agus Harno Nurdin Syah
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
