Facing Evaluation on Vacuum Assisted Resin Infusion (Vari) Co-Cured Sandwich Composites: Inlet and Outlet Comparison
DOI:
https://doi.org/10.55981/ijoa.2026.13523Keywords:
sandwich composite, vacuum-assisted resin infusion, co-cure, thickness variation, tensile propertiesAbstract
Sandwich composites are preferred in marine or aerospace applications due to their superior specific flexural properties. Low-cost, high-quality sandwich composites can be produced using the co-curing method with the Vacuum Assisted Resin Infusion (VARI) manufacturing technique. However, manufacturing composites with VARI results in thickness variation between the resin inlet and vacuum outlet, thus affecting the uniformity of mechanical properties. This study evaluated the facing properties variation of sandwich composites fabricated using the VARI co-cure method with different numbers of facing plies. Sandwich composites were fabricated with carbon fiber/epoxy and PVC foam using the VARI co-cure method with central linear infusion. The thickness, fiber volume fraction, and tensile properties of the facings were evaluated at the resin inlet and the vacuum outlet for comparison. The sandwich composites were successfully fabricated using the VARI co-cure method. The facing properties between the resin inlet and vacuum outlet have variations of 2,6-15.0 % in thickness, 0.7-5.5 % in fiber volume fraction, 3.6-6.2 % in tensile modulus, and 5,7-35.17 % in tensile strength. Upper facings tend to have a higher property variation than lower ones. As the number of facing plies increases from 2 to 6, the thickness variation and the fiber volume fraction also increase, resulting in a higher variation in tensile modulus and strength.
References
Caliskan, Umut, and M. Kemal Apalak. 2020. “The Response of Pin-Clamped Carbon Fibre-Reinforced Plastics Composite Sandwich Beams with Polyvinylchloride Foam Core under Bending Impact.” Journal of Reinforced Plastics and Composites 39(9–10):384–405. doi: 10.1177/0731684420910794.
Halimi, F., M. Golzar, P. Asadi, and M. H. Beheshty. 2013. “Core Modifications of Sandwich Panels Fabricated by Vacuum-Assisted Resin Transfer Molding.” Journal of Composite Materials 47(15):1853–63. doi: 10.1177/0021998312451763.
Hancioglu, Mert, E. Murat Sozer, and Suresh G. Advani. 2020. “Comparison of In-Plane Resin Transfer Molding and Vacuum-Assisted Resin Transfer Molding ‘Effective’ Permeabilities Based on Mold Filling Experiments and Simulations.” Journal of Reinforced Plastics and Composites 39(1–2):31–44. doi: 10.1177/0731684419868015.
Jhan, Yu Ti, Ya Jung Lee, and Cheng Hsien Chung. 2011. “Resin Flowing Analysis in Sandwich Laminates under VARTM Process.” Journal of Reinforced Plastics and Composites 30(6):533–45. doi: 10.1177/0731684411399142.
Jhan, Yu Ti, Ya Jung Lee, and Cheng Hsien Chung. 2012. “Experimental and Numerical Investigation of the VARTM Process with a Sandwich Structure.” Journal of Composite Materials 46(12):1417–30. doi: 10.1177/0021998311418703.
Kazmi, S. M. R., Q. Govignon, and S. Bickerton. 2019. “Control of Laminate Quality for Parts Manufactured Using the Resin Infusion Process.” Journal of Composite Materials 53(3):327–43. doi: 10.1177/0021998318783308.
Li, Jing, Chuck Zhang, Richard Liang, Ben Wang, and Shawn Walsh. 2008. “Modeling and Analysis of Thickness Gradient and Variations in Vacuum-Assisted Resin Transfer Molding Process.” Polymer Composites 29(5):473–82. doi: 10.1002/pc.20439.
Manalo, A. C., T. Aravinthan, and W. Karunasena. 2013. “Mechanical Properties Characterization of the Skin and Core of a Novel Composite Sandwich Structure.” Journal of Composite Materials 47(14):1785–1800. doi: 10.1177/0021998312451607.
Menta, V. G. K., R. R. Vuppalapati, K. Chandrashekhara, D. Pfitzinger, and N. Phan. 2012. “Manufacturing and Mechanical Performance Evaluation of Resin-Infused Honeycomb Composites.” Journal of Reinforced Plastics and Composites 31(6):415–23. doi: 10.1177/0731684412439792.
Modi, D., M. Johnson, A. Long, and C. Rudd. 2007. “Investigation of Pressure Profile and Flow Progression in Vacuum Infusion Process.” Plastics, Rubber and Composites 36(3):101–10. doi: 10.1179/174328907X177608.
Rubino, Felice, and Pierpaolo Carlone. 2019. “A Semi-Analytical Model to Predict Infusion Time and Reinforcement Thickness in VARTM and SCRIMP Processes.” Polymers 11(1). doi: 10.3390/polym11010020.
Rusnáková, Soňa, and Milan Žaludek. 2018. “The Limits of Vacuum Infusion Technology during the Production of Filled Polymer Composite Systems.” Materials Science Forum 919:175–81. doi: 10.4028/www.scientific.net/MSF.919.175.
Tackitt, Kirk D., and Shawn M. Walsh. 2005. “Experimental Study of Thickness Gradient Formation in the Vartm Process.” Materials and Manufacturing Processes 20(4):607–27. doi: 10.1081/AMP-200041896.
Yalkin, Huseyin Erdem, Bulent Murat Icten, and Tuba Alpyildiz. 2015. “Enhanced Mechanical Performance of Foam Core Sandwich Composites with through the Thickness Reinforced Core.” Composites Part B: Engineering 79:383–91. doi: 10.1016/j.compositesb.2015.04.055.
Yenilmez, Bekir, Murat Senan, and E. Murat Sozer. 2009. “Variation of Part Thickness and Compaction Pressure in Vacuum Infusion Process.” Composites Science and Technology 69(11–12):1710–19. doi: 10.1016/j.compscitech.2008.05.009.
Yokozeki, Tomohiro, Wataru Yamazaki, and Yayoi Kobayashi. 2015. “Investigation into Property Control of VaRTM Composites by Resin Infusion Process.” Advanced Composite Materials 24(6):495–507. doi: 10.1080/09243046.2014.919432.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2026 Rijal Ahmadi, Hermawan Judawisastra, Riza Wirawan

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.


