Effect of Laser Scanning Speed on Wettability and Lap Shear Strength of Laser-Engraved Carbon/Epoxy Single-Lap Joints
DOI:
https://doi.org/10.55981/ijoa.2026.15928Keywords:
laser engraving, single lap joint, CFRP, adhesive bonding, wettabilityAbstract
Adhesive bonding is widely used for joining CFRP composite structures because it provides a lightweight, continuous, and structurally efficient connection compared with conventional joining methods. However, the relationship between laser scanning speed, surface characteristics, and bonding performance in CFRP single-lap joints remains insufficiently clarified, particularly compared with conventional mechanical abrasion. In this study, the effect of laser scanning speed on wettability and lap shear strength of laser engraved carbon/epoxy single-lap joints were investigated. Untreated and 800-grit sanded surfaces were used as references. The carbon/epoxy adherends were manufactured by Vacuum-Assisted Resin Infusion (VARI) and bonded with Araldite 420 according to ASTM D5868. Surface properties were studied by contact angle and roughness measurements, mechanical performance was studied by lap shear testing. The maximum lap shear strength was achieved at 50 mm/s, 12.530 ± 1.230 MPa, which is more than 45% higher than the untreated and sanded conditions. However, the difference in contact angle was not statistically significant but laser-treated specimens showed higher joint strength, indicating that the improvement of bonding was mainly due to the surface morphology modification by laser and mechanical interlocking. These results further show the importance of the laser scanning speed for the improvement of adhesive bonding of CFRP.
References
Abdurohman, K., Widianto, T., & Pasadena, W. (2024). Influence of abrasion treatments on performance of adhesively bonded composite joints. Evergreen, 11(2), 806–820.
ASTM D5868-01. (2014). Standard test method for lap shear adhesion for FRP bonding. ASTM International.
Banea, M. D., & da Silva, L. F. M. (2016). Adhesively bonded joints in composite materials: An overview. Proceedings of the Institution of Mechanical Engineers, Part L, 230(1), 1–18.
Chen, D., Arakawa, K., & Xu, C. (2015). Reduction of void content of vacuum-assisted resin transfer molded composites by infusion pressure control. Polymer Composites, 36(9), 1629–1637. https://doi.org/10.1002/pc.23071
da Silva, L. F. M., Öchsner, A., & Adams, R. D. (2018). Handbook of adhesive bonding (2nd ed.). Springer.
Gai, D., Yao, Z., Xu, H., Yang, K., Yang, S., & Yu, S. (2024). Mechanical and failure analysis of adhesive joints of CFRP under hygrothermal conditions. International Journal of Adhesion and Adhesives, 134, 103793.
Kinloch, A. J. (2012). Adhesion and adhesives: Science and technology. Springer.
Kuentzer, N., Simacek, P., Advani, S. G., & Walsh, S. (2007). Correlation of void distribution to VARTM manufacturing techniques. Composites Part A: Applied Science and Manufacturing, 38(3), 802–813. https://doi.org/10.1016/j.compositesa.2006.08.005
Liu, Z., Wang, H., Chen, Y., & Hua, L. (2024). Laser-induced surface reconstruction to enhance interfacial bonding reliability of CFRP/titanium hybrid joints. Journal of Materials Research and Technology, 32, 3523–3536. https://doi.org/10.1016/j.jmrt.2024.08.099
Mendiratta, M., & Prakash, S. (2025). Adhesive bonding of CFRP utilizing nanosecond laser texturing for pre-surface treatment in different processing environments. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 240(2), 532–549. https://doi.org/10.1177/09544062251381415
Peng, T. Y., Shimoe, S., Higo, M., Kato, M., Hirata, I., Iwaguro, S., & Kaku, M. (2024). Effect of laser engraving on shear bond strength of polyetheretherketone to indirect composite and denture-base resins. Journal of Dental Sciences, 19(1), 32–38. https://doi.org/10.1016/j.jds.2023.06.005
Petrie, E. M. (2013). Handbook of adhesives and sealants (2nd ed.). McGraw-Hill.
Shakeri, M., & Akbarzadeh, A. (2017). Surface treatment methods for adhesive bonding of composites: A review. Journal of Adhesion Science and Technology, 31(18), 2005–2038.
Shin, J., Kim, H., & Lee, D. (2021). Effect of laser surface texturing on adhesion characteristics of CFRP composites. Applied Surface Science, 542, 148592.
Sorrentino, L., Marfia, S., Parodo, G., & Sacco, E. (2020). Laser treatment surface: An innovative method to increase the adhesive bonding of ENF joints in CFRP. Composite Structures, 233, 111638. https://doi.org/10.1016/j.compstruct.2019.111638
Stribick, S., & Alhadad, B. (2025). Laser surface texturing for surface preparation of adhesive bonding of polypropylene. The International Journal of Advanced Manufacturing Technology, 140, 4339–4354. https://doi.org/10.1007/s00170-025-16466-y
Wei, Y., Jin, X., Luo, Q., Li, Q., & Sun, G. (2024). Adhesively bonded joints – A review on design, manufacturing, experiments, modeling and challenges. Composites Part B: Engineering, 111225. https://doi.org/10.1016/j.compositesb.2024.111225
Wen, L., Wang, R., & Xu, E. (2024). Optimization and mechanism study of bonding properties of CFRP/Al7075 single-lap joints by low-temperature plasma surface treatment. Coatings, 14(5), 541. https://doi.org/10.3390/coatings14050541
Yang, G., Yang, T., Yuan, W., & Du, Y. (2019). Influence of surface treatment on tensile properties of CFRP bonded joints. Composites Part B: Engineering, 160, 446–456.
Zhang, A., Jiang, H., Li, Y., Hu, R., Ren, Y., & Jiang, S. (2024). Effects of surface micro-texturing laser-etching on adhesive property and failure behaviors of basalt fiber composite single-lap-joint. International Journal of Adhesion and Adhesives, 135, 103831. https://doi.org/10.1016/j.ijadhadh.2024.103831
Zhang, J., Wang, X., & Li, Q. (2020). Effect of mechanical surface treatment on bonding performance of composite joints. Materials Today Communications, 25, 101563.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2026 Ryan Hidayat, Mohammad Adhitya, Rezky Agung Pratomo, Kosim Abdurohman

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.


