KARAKTERISTIK BIOPELET DARI LIMBAH PADAT KAYU PUTIH DAN GONDORUKEM
Main Article Content
Abstract
Biopelet is a solid fuel made of forging a cylindrical biomass and it could be used as an alternative energy. Cajuput
and pine resin wastes are two potential material for biopellet. Biomass fuel in the form of biopellet provide better heat
quality than direct biomass combustion. This paper studies the particle size and process temperature in producing
optimum and environmentally friendly biopellet. Raw materials of cajuput and pine resin wastes were mixed, powdered
and sieved into 20, 40, 60 and 80 mesh. Thirty grams of each powder was molded with the composition of 70%
cajuput solid waste and 30% of pine resin. Biopellet was compressed using compression hydraulic press machine of
526.48 kg/cm2 with a temperature of 120, 150, 180, 200, 230 and 260°C. The results showed that the biopellet
made of 40 mesh mixed powder and temperature process of 230°C produced the optimum quality of biopellets.
Thr physical properties of the biopellet made of 40 mesh powder and 230°C processing temperature were: 1.905%
moisture content; 3.955% ash content; 72.189% vollatile matter; 21.949% fixed carbon; 5,097.5 kcal/kg calorific
value and compression strength of 53.746 kgf/cm2.
Article Details
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
References
Ali, A., & Restuhadi, F. (2010). Optimasi pembuatan biopelet dari bungkil picung (Pangium edule Reinw.) dengan penambahan solar dan perekat tapioka. Sagu, 9(1), 1-7.
Basu, P. (2010). Biomass gasification and pyrolisis, practical design and theory. US: Academic Press.
Bergman, R., & Zerbe, J. (2008). Primer on wood biomass for energy. Diakses dari http://www.fpl.fs.fed.us/documnts/fpmu/biomass_energy/primer_on_wood_biomass_for_energy.pdf pada tanggal 25 Mei 2016.
Bridgwater, A. V. (2012). Review of fast pyrolysis of biomass and product upgrading. Biomass and Bioenergy, 38, 68–94. doi: 10.1016/j.biombioe.2011.01.048.
Carone, M.T., & Pantaleo, A. (2011). Influenca of process parameters and biomass characteristics on the durability of pellets from the pruning residues of Olea europaea L. Biomass Bioenergy, 35(1), 402-410.
Chou, C. S., Lin, S. H., Peng, C. C., & Lu, W. C. (2009). The optimum conditions for preparing solid fuel briquette of rice straw by a piston-mold process using the Taguchi method. Fuel Processing Technology, 90(7-8), 1041–1046. doi.org: 10.1016/j.fuproc.2009.04.007
Fang, S., Tang, L.L., & Zhai, J. (2013). Clonal variation in growth, chemistry and caloric valie of new polar hybrids at nursery stage. Biomass Bioenergy, 54, 303-311.
Hansen, M.T., Jein, A.R., Hayes, S., & Bateman, P. (2009). English handbook for wood pellet combustion. Europe: National Energy Foundation.
Hendra, D., & Darmawan, S. (2000). Pembuatan briket arang dari serbuk gergajian dengan penambahan tempurung kelapa. Buletin Penelitian Hasil Hutan, 18 (1), 1-9.
Hendra, D. (2012). Rekayasa pembuatan mesin pelet kayu dan pengujian hasilnya. Jurnal Penelitian Hasil Hutan, 30(2), 144–154.
Kaliyan, N., & Morey, R.V. (2009). Factors affecting strength an durability of densified biomass products. Biomass Bioenergy, 33(3), 337-359.
Kartikasari, D. (2007). Studi pengusahaan minyak kayu putih (cajuput oil) di PMKP Jatimunggul, KPH Indramayu Perum Perhutani Unit III Jawa Barat dan Banten. (Skripsi). Institut Pertanian Bogor, Bogor.
Kementerian Lingkungan Hidup dan Kehutanan. (2017). Statistik lingkungan hidup dan kehutanan tahun 2016. Jakarta.
Lamers, P., Junginger, M., Hamelinck, C., & Faaij, A. (2012). Developments in international solid biofuel trade An analysis of volumes, policies, and market factors. Renewable and Sustainable Energy Reviews, 16(5), 3176–3199. doi: 10.1016/j.rser.2012.02.027.
Lehtikangas, P. (2001). Quality properties of pelletised sawdust, logging residues and bark, Biomass and Bioenergy, 20, 351–360.
Liliana, W. (2010). Peningkatan kualitas biopelet bungkil jarak pagar sebagai bahan bakar melalui teknik karbonisasi. (Tesis). Program Pascasarjana, Institut Pertanian Bogor, Bogor.
Muharyani, R., Pratiwi, D., & Asip, F. (2012). Pengaruh suhu serta komposisi campuran arang jerami padi dan batubara subbituminus pada pembuatan briket bioarang. Jurnal Teknik Kimia, 18(1), 47–53.
Nilsson, D., Bernesson, S., & Hansson, P. (2010). Pellet production from agricultural raw materials: A system study. Biomass and Bioenergy, 35(1), 679–689. doi: 10.1016/j.biombioe.2010.10.016.
Nurwigha, R. (2012). Pembuatan biopelet dari cangkang kelapa sawit dengan penambahan arang cangkang sawit dan serabut sawit sebagai bahan bakar alternatif terbarukan. (Skripsi). Institut Pertanian Bogor, Bogor.
Onu, F., Rahman, M.B.N., & Sudarja. (2010). Pengukuran nilai kalor bahan bakar briket arang kombinasi cangkang pala (Myristica fragan Houtt) dan limbah sawit (Elaeis guineensis). Prosiding Seminar Nasional Teknik Mesin UMY. ISSN: 2087-1368
Pari, G. (2004). Kajian struktur arang aktif dari serbuk gergaji kayu sebagai adsorben emisi formaldehida kayu lapis. (Disertasi Doktor). Program Pasca Sarjana, Institut Pertanian Bogor, Bogor.
Poddar, S., Kamruzzaman, M., Sujan, S.M.A., Hossain, M., Jamal, M.S., & Khanam, M. (2014). Effect of compression pressure on lignocellulosic biomass pellet to improve fuel properties: Higher heating value. Fuel 131, 43-48. doi:10.1016/j.fuel.2014.04.061.
Prasetyo, B. (2004). Pengaruh jumlah perekat dan variasi besar tekanan kempa terhadap kualitas briket arang dari sabutan kayu jati, sonokeling, dan kelapa. Yogyakarta: Universitas Gajah Mada.
Qian, F.P., Chyang, C.S., Huang, K.S., & Tso, J. ( 2011). Combustion and NO emission of high nitrogen content biomass in a pilot-scale vortexing fluidized bed combustor. Bioresource Technology, 102 (2), 1892–1898. doi.org/10.1016/j.biortech.2010.08.008.
Rusdianto, A.S. (2013). Kajian potensi penggunaan by product industri pertanian di Kabupaten Jember sebagai bahan baku pembuatan biopelet untuk bahan bakar alternatif. Fakultas Teknologi Pertanian, Universitas Jember, Jember.
Rusdianto, A.S., Choiron, M., & Novijanto N. (2014). Karakterisasi limbah industri tape sebagai bahan baku pembuatan biopelet. Jurnal Industrialisasi, 1(3), 27-32.
Samuelsson, R., Larsson, S. H., Thyrel, M., & Lestander, T. A. (2012). Moisture content and storage time influence the binding mechanisms in biofuel wood pellets. Applied Energy, 99, 109–115. doi: 10.1016/j.apenergy.2012.05.004.
Saputro, D.D., Widayat W., Rusiyanto, Saptoadi H. & Fauzan. (2012). Karakterisasi briket dari limbah pengolahan kayu sengon dengan metode cetak panas. C. Kurniawan (Ed.) Prosiding Seminar Nasional Aplikasi Sains & Teknologi (SNAST) 2012.
Setiawan. (2007). Memanfaatkan kotoran ternak, solusi masalah lingkungan dan pemanfaatan energi alternatif. Depok: Penebar Swadaya.
Shen, D. K., Gu, S., Luo, K. H., Bridgwater, A. V, & Fang, M. X. (2009). Kinetic study on thermal decomposition of woods in oxidative environment. Fuel, 88(6), 1024–1030. doi.org: 10.1016/j.fuel.2008.10.034.
Standar Nasional Indonesia (SNI). (2014). Pelet kayu. (SNI 8021-2014). Badan Standardisasi Nasional.
Sukmananto B. (2014). Perum Perhutani pelopor bisnis hijau. Makalah disampaikan dalam Seminar Nasional Silvikultur ke-2 di Yogyakarta, 28 Agustus 2014.
Taylor, R. E., Butzelaar, P., Leeuwen, G. V., Palmer, A., Keyes, J., Gimenez, C. & MacDonald, B. (2013). Wood pellet market outlook. Wood Market International Monthly Report, 18(1), 1-3.
Wibowo, T., Setyawati, D., Nurhaida, & Diba, F. (2016). Kualitas biopelet dari limbah batang kelapa sawit dan limbah kayu penggergajian. Jurnal Hutan Lestari, 4(4), 409-417.
Yilmaz, S., & Selim, H. (2013). A review on the methods for biomass to energy conversion systems design. Renewable and Sustainable Energy Reviews, 25(c), 420-430.
Yuniarti., Arhamsyah., Faisal, Y., & Theo, Y.P. (2011). Briket arang dari serbuk gergajian kayu meranti dan arang kayu galam. Jurnal Riset Industri Hasil Hutan, 3(2), 37-42.
Zulfian, Diba, F., Setyawaty, D., Nurhaida, & Roslinda, E. (2015). Kualitas biopelet dari limbah batang kelapa sawit pada berbagai ukuran serbuk dan jenis perekat. Jurnal Hutan Lestari, 3(2), 208-216.
